Axminster C0 Operations Instructions

Code 508203AXMINSTERSERIESHobbyHBS205N 8" Bandsaw

Illustration and Parts Description10Mitre fence assembly (A) Index and pointer (B)Blade guide adjusting knob (A) Blade guide clamp (B)Blade tensioning

Illustration and Parts Description11Upper blade guide clampUpper blade guide adjusting knobMItre fenceTable insertSaw tableTilt mechanismTilt mechanis

Illustration and Parts Description12Lower blade guide assembly (A) Blade guide pin and clamping grub screw (B)Lower blade guide guard (A) Rear thrust

Illustration and Parts Description13Lower saw wheelFence clamping leverDust extraction outletSaw wheel brushUpper saw wheelUpper wheel mountingBlade g

Setting Up the Saw14DISCONNECT THE SAW FROM THE MAINS SUPPLY!DISCONNECT THE SAW FROM THE MAINS SUPPLY!Tensioning and tracking the bladeMake sure both

Setting Up the Saw15Checking the table is squareIf the preset table stop has been fitted, proceed as follows:-Loosen the butterfly nut clamping the tilt

Setting Up the Saw16Setting the Blade GuidesLower the upper blade guide to approximately 1 1/2”(38mm) above the table by loosening the blade guide hei

Setting Up the Saw17Fig 27Guide pinSetting the Lower Blade GuidesNOTE: For easier access to the lower blade guides it is recommended you remove the ta

Operating Instructions18Do not try to cut too quickly; the correct cutting speed, if one could be so precise, would never see the blade pushed back ag

Changing the Saw Blade19mounting assembly could likewise be lightly oiled. If you are fitting a new blade it will have been supplied to you “folded”,

Index of Contents2Declaration of ConformityCopied from CE CertificateThe undersigned, T. Fuhrmann Authorised by Qingdao D&D Electromechanical Tec

Routine Maintenance20Daily• Keep the machine clean. • Check the saw blade for missing teeth andcracks, see fig 34. • Spray oil the bare metal surfaces.

Parts Breakdown/List21

Parts Breakdown/List22ITEM PART NO. NAME Q’ty1 DJ200020200 Rip fence assembly 12 DJ200020103A Support 33 31503009A Locking knob 14 DJ200020101D Workin

Parts Breakdown/List23ITEM PART NO. NAME Q’ty35 DJ200030801 Saw blade 136 GB5783-86 M6×12 Hex Bolt 837 31503030 Tongue 238 31503033 Housing with nut

Parts Breakdown/List24ITEM PART NO. NAME Q’ty69 DJ200020108 Plank 170 DJ200020102 Locking handle 171 DJ200030406 Locking knob 172 DJ250A05005 Power co

Wiring Diagram25

Bandsaw Blades26Standard Axcaliber Bandsaw BladesAxminster HBS310N Bandsaw6 1/4" 50825310 1/4" 50825414 1/4” 50825524 1/4” 50825632 1/4”

Notes27

Axminster Tools & Machinery LtdWeycroft Avenue, Axminster, Devon EX13 5PHaxminster.co.ukPlease dispose of packaging for the product in a responsib

What’s Included3Quantity Item Part Model Number RBS205 1 No HBS205N 8" Bandsaw A (Code: 508203)1 No Bandsaw Blade 1,400mm Long 6” TPI

What’s Included4EFCDMLKJHIG

General Instructions for 230V Machines5Good Working Practices/Safety Primary PrecautionsWork Place/EnvironmentThe following suggestions will enable y

General Instructions for 230V Machines6Check that blades are the correct type and size, are undamaged and are kept clean and sharp, this will maintain

Assembly7Fig 02Step 1 Locate the bandsaw table (B), the four M6 bolts (G) and shake proof washers (H). Slot the blade into the table’s slot and line u

Assembly8Fig 08Fig 07DFence rail “T” slotClamping leverStep 4 Locate the angled bolt (K), screw the threaded end of the bolt into the threaded hole t

Illustration and Parts Description9Lower wheel doorGuide fenceUpper door locking screwLower door locking screwUpper blade guide and guardFence guide r